- STSW STM32102 INSTALL
- STSW STM32102 DRIVERS
- STSW STM32102 UPDATE
- STSW STM32102 MANUAL
- STSW STM32102 WINDOWS
Quick version Manual tuning via TS Open TS, and guess at your fuel table, it will probably look similar to the below. Then tune the wall wetting, then tune the cold start conditions. This tutorial is just a suggestions, and will suggest you first start with a warm engine and tune the load table such that you get the AFR's that you are looking for. This tutorial is going to make some suggestions and keep in mind there are going to be lots of different opinions and different reasons for doing things differently. Every one has a different tuning preference for a variety of reasons, some good some not so good. There is also a bunch of tuning to deal with the short term dynamic conditions, as well there is tuning for cold engine conditions, etc. The tuning tables are mostly for tuning the steady state conditions. As well if you have a 4 cyl Miata with a turbo, you might be at around 30% under these same conditions. However if you have a 4 cyl Miata, then your load under the same conditions as noted above would be about 40% instead of 20%, which means your tuning table will be adjusted differently at different points. You will take your best stab to guess what is the most optimal way to get to the finish line fastest. So your tuning table around the 20% would be tuned to have an AFR around 16, while when at 100% load your tune will be tuned for something closer to 11. Then when you are say 80% or 100% load you want maximum power, as you do not have enough power and you want every Hp you can get. Such that you get the most out of the fuel in the tank. At this point you have enough power and you want to minimize fuel consumption. If you have a V8 in a Miata, and you need a lite load perhaps like when approaching a turn, you might have a load around 20%.
The below graphic shows how you vary horse power as you change AFR. Every person will be differ in what RPM and loads they want power vs fuel efficiency. This commonly means you are looking for minimal fuel consumption when you are maintaining speed or decreasing speed, then max power when you are at higher engine loads. This section assumes you are looking for fast track times. Fuel tuning Some quick theory Most people who do the after market ECU are looking to get around the track faster. Verify that TDC is correct by shining on a crank wheel like a timing light. At this point you should the the RPM varying on the Java Console. Specify that COM port and verify it's connects.
The most useful feature is the plain signal sniffer - both real inputs and generated signals can go into it and this is actually quite handy.
Also note, it as some functionality as noted below. Play around with it and see what you can learn. Update: there is also a lazier way to self-stimulate now, you would not need the jumper wires.
STSW STM32102 INSTALL
Now install gray jumper wire as noted above between pins PD1 and PC6. However you can specify that when you launch it by specifying a command line parameter as noted below.
STSW STM32102 WINDOWS
When you do this for the first time, on a Windows PC, you will be prompted for drivers. This will provide power to the Discovery board. To get the console working follow the below procedure, which assumes you have loaded the rusEFI firmware. Here are some pictures of what it looks like when it operating correctly. The console allows firmware monitoring and configuration. The dev console is written in java and it talks to the ECU firmware. If all is good, proceed to the Dev Console below. After you hit the reset button, you should expect all four LEDs to blink once and then you should see just the blue LED blinking. Plug in the black cable and install jumpers as shown below.
STSW STM32102 UPDATE
See below procedure found Load firmware Before loading rusEFI firmware - if you have one of the newer Rev D STM32 discovery boards - you need to update discovery's firmware. Mini-USB cable is used to power and to program the brain board. We are a website that provides information about the key to the answer, education, physical subjects, subjects chemistry, mathematical subjects. Jumpers Communication mode microUSB channel is more sensitive to noise but it's faster See also Configuration reset Grounding PD6 resets saved configuration to default state - see Board Testing mode Grounding PB0 enables board testing mode.
STSW STM32102 DRIVERS
※ Download: ?dl&keyword=Stsw-stm32102+driver+download&source=Ĭan you try plugging it into another USB port on your PC and just leaving it for about half an hour with your PC connected to the net? Please scroll down to find a latest utilities and drivers for your STM32 BOOTLOADER driver.
0 kommentar(er)
